Wax cartridges ensure a smoother, clean and more convenient way to apply wax. Your hair will be removed from the root with this method so over time it gradually becomes thinner and takes approximately 3 weeks before growing back until hardly at all. If you enjoy waxing your unwanted body hair or you would like to give it a go; then keep reading as we will go over everything you will need to know for a successful treatment with a wax cartridge.
You will need:
Wax Cartridge – Either with a large or mini roller head; depending on the area you intend to wax.
Cartridge Heater – a simple heater has proven to be as sufficient.
Wax Paper Strips – You can either purchase a roll of the paper or the strips which are already cut into relevant sizes. Upon the attempt to be economical and purchasing cheapest depilation paper, it may tear so it’s better not to try to save on this item. The middle-range will be sufficient.
Antiseptic Gel – Applied prior to the procedure which will sterilize the skin.
Talcum Powder – Wax does not like moisture on the skin, so powder dries and degreases the skin prior to wax application. A small amount of powder is also ideal for delicate areas such as the eyebrows or upper lip as it provides a protective barrier between the skin and the wax. It’s cheap and lasts a long time.
Oil – Basically any oil will be suitable. After the waxing procedure is over, oil is the most effect way to remove wax residue left on the skin. It will also moisturize the skin.
Prior to the Procedure:
Shower and clean the skin thoroughly 2 hours before to ensure your skin will be completely dry.
Ensure your hair is at least 4-5m.
- Remove the protective film from the cartridge and insert it into the heater. After approximately 20-25 minutes, the cartridge will have reached the ideal temperature. See the instruction here.
- Ensure the hairy skin is dry and then apply the antiseptic gel or talcum powder to absorb any excess moisture.
- Once the wax has finished heating up, take it out of the heater and turn the heater of. Turn the applicator upside down for a few seconds in order to stack the wax so that it’s evenly distributed throughout the roller. Now it’s time to apply the wax. In the direction of hair growth apply a thin strip about 5-10cm in length.
- Cover and press firmly with a paper strip in the direction of the hair growth. Keep about 1cm at the end free so that you can easily pull off the strip without coming into contact with the wax.
- Now hold your skin tight from the top of the strip and from the bottom; using the little tab you left, grab and tear the strip off in one sharp movement. Ensure to pull along the skin and not directly up. If the occurrence of hair is still there, then just repeat the same procedure again. When wax is left on the sides, just simply apply the strip over that area and the wax will come when the strip is removed.
- Repeat this procedure until you are happy with your final result. The same wax strip can be used again and again during one procedure until you see that the wax buildup on the strip is 2-3mm. If the wax cools down, just put it back in the heater and warm it back up.
After the Wax:
Apply oil immediately to the area, using massage movements until the wax remnants are gone.
- Keep your skin dry for at least 6 hours after the procedure in order to avoid infections and irritations.
- For 24 hours after the wax, do not take a hot bath, shower or visit a sauna as this will cause your pores to open leaving you vulnerable to an infection.
- No tanning for 24 hours, as the skin will be sensitive.
- Avoid fragrance products as they may cause irritation.
- Don’t wear tight clothing.
- After 3-4 days you may use scrubs on the area, then 2-3 times per week is ideal in order to prevent ingrown hairs.
Waxing with a cartridge is a hygienic and quick method that can be used virtually anywhere on the body; it’s great for those who are new to at home waxing or want an alternative to the messy pot wax.
Hair care expert